Question about the preset pH values in the display of the EOS Touch | Values are quite high even at level 1 | Acidic water not acidic enough
Hello Mr Akgün,
Thank you for getting in touch and for extending the test phase.
I actually have two problems, one of which I think I've solved by playing around with the settings. (Set PH value correctly)
You said in a YouTube video that you should set the raw PH value to 6,6PH so that the device works at its strongest.
However, this meant that even with the highest flow rate (2,1L) that was possible for me on level 1, the values were far too high to start drinking
The following:
Level 1: 9,1
Level 2 9,3
Level 3 9,6
Level 4 10,2
Level 5 10,5
Now I went and set the raw PH value to 7,9.
Now at least the first steps are correct so that you can start with test drinking.
Here's what I measured:
Level 1 8,8
Level 2 9,1
Level 3 9,3
Level 4 9,6
Level 5 10,0
I actually only have one thing in mind for the acidic water. I just want to run the water through the outlet tap at the highest level every morning for disinfection. You mentioned this in a YouTube video.
But since I can't get below 6,5PH to level 4 acid with 0,8L flow at the outlet, I think there's no disinfection at this PH value, right?
Is there another way to disinfect the outlet tap?
At what pH value does disinfection take place?
The device should actually get below 6,5 at the outlet tap, right?
Thanks for the reply and for the help.
It's not that easy to work your way into it :))
LG Frederik Schmitz
Answer from Yasin Akgün | Without the addition of salt, there is no reliable anolyte / disinfectant, acidic water
Hello Mr. Schmitz
You cannot make water as acidic as you like without adding salt.
The most acidic water you get is 0,8 liters of water, namely the water from the sewer hose. Speak÷
Level 4 Press alkaline, flow to 0,8 liters/min, and then the acidic wastewater from the wastewater hose, which could possibly be pH 5.
What exactly is your goal?
You could mobile produce a neutral anolyte, i.e. both waters in one:
www.aquacentrum.de/shop/aquacentrum-blue-700-hydrogen-water-maker-hrw/
Or as a spray: www.aquacentrum.de/shop/aquacentrum-beauty-blue-500-hydrogen-water-maker-hrw/
Or professionally, this slightly larger device:
www.aquacentrum.de/shop/aquavolta-eca-water-tractor-eca-anlage/
I'd like to know what you're up to so I can give you more tips.
Due to the free trial period, it is extended by another week.
The EOS devices are truly the best and tastiest, don't let the sour water issue confuse you.
All the best
Yours, Yasin Akgün
Question from Mr Schmitz | There isn't really any acidic water coming out of the top of the outlet
Hello Mr Akgün,
Would you have any more information for me regarding the question of how best to disinfect the outlet of the water ionizer because with the acidic water level 4 I only get a PH value of 6,5 with a flow of 0,8L?
I also have a second question.
..if you want to take the water in the blue bottles with you to work, what higher PH value would you recommend so that you can drink it throughout the day to still benefit from the high PH value?
Over time, a little bit of hydrogen is lost and the PH value drops.
LG and thanks in advance.
Frederik Schmitz
Reply Yasin Akgün | Regular disinfection by descaling the water ionizer with citric acid and a dash of hydrogen peroxide
Hello Mr. Schmitz
Thanks for your question.
Now I know what you want, disinfect the outlet.
I would rather descale and disinfect every 14 days or so with citric acid and a little hydrogen peroxide.
Everything else doesn't work with the device, from the waste water hose it can reach pH 5, depending on your water, but not from above, because the ratio there is twice as high, so everything is diluted.
Otherwise, you could use a funnel to pour in a little hydrogen peroxide every now and then and let it work if you have any concerns.
Hope this helps you
Love greetings
Yasin Akgun
