Allsbon Dion Blue water ionizer used

Video: Allsbon Dion Blue and Family in comparison:

Allsbon Dion Blue water ionizer

The Allsbon Dion Blue Based on our practical experience, it is one of the most modern and technically sophisticated water ionizers or table water systems on the water ionizer or drinking water treatment market.

Of all the water ionizers we have tested so far, the Dion Family and other Allsbon devices have 9 electrodes with distance the highest pH values ​​and redox potentials. You can still achieve high pH values ​​around pH-4 with a maximum flow of 9 liters per minute. Standard water ionizers with 5 or 7 electrodes only manage pH 3 or even less at 8 liters per minute.

Also the Hydrogen content Compared to other water ionizers, it is the highest that Mr. Karl Heinz Asenbaum was able to determine. So the Dion Special is the one for us of all the water ionizers currently available first choice.

Multifunctional display: Displays the pH value, the redox potential and the water flow

The pH and redox values ​​shown on the display apply to medium hardness levels and flow rates of around 2 liters / minute

Hardly any other water ionizer can keep up with the clear arrangement of the touch buttons (touch control sensors) and the information displayed on the very elegant display in terms of ease of use and design.

The total filter running times of both filters are shown in liters on the display

The filter running times for both filters are shown separately and to the liter in the display. This means you always have an overview of how much water you have already used.

As soon as a filter change is necessary, the inherent diagnostic module becomes active and also shows you the required filter change on the display. In addition, a voice output draws your attention to the change. This saves you additional maintenance work.

You can also trigger a warning after certain filter runtimes in the fine settings in the menu. E.g. after 6 months for the first (filter on the left) and also the second filter (filter on the right from the back) after 5000 liters. By default, the water ionizer warns you after 5000 liters.

However, we recommend ignoring the filter cycle times shown on the display and replacing at least the first filter after 6-9 months at the latest.

After a change, you can view the filter runtime display of the respective filter by tapping and then holding down the buttons “FILTER 1” or “FILTER 2” reset to default.

9 titanium electrodes, triple electroplated with platinum for very high values

The platinum-coated titanium electrodes (plus-minus poles) perform the fundamental role of separating purified water into alkaline and acidic water. However, there are huge differences in the basicity and quality of the activated water of the various water ionizers, which are determined by the thickness and type (galvanically applied or sprayed) the platinum-titanium coating and the number of electrodes as a whole can be achieved.

Each of the 9 electrodes is solidly dip-coated with three electroplated layers of platinum. In contrast to water ionizers with 5 or 7 electrodes, the 9-electrode ionizer is also suitable for very hard tap water above °dH 27; values ​​up to pH 10,5 and above can be safely and permanently achieved even with hard water.

An additional advantage of platinum titanium coating is that it has high electrical conductivity and is a harmless material to the human body. Furthermore, the heart of the Allsbon Dion water ionizer is characterized by extremely low power consumption and good electrolytic performance. Extremely accurate pH and redox potential (ORP) values ​​can be achieved.

Transformerless SMPS power supply for minimal heat and electrosmog load

Classic power transformers (transformers), which are widely used in water ionizers, are only designed to withstand a power supply of 100-150W/24-30V/5A. As a result, a lot of PCB program errors or malfunctions occur because individual components overheat, which generates excess current during the electrolysis process. Instead, Allsbon is consistent SMPS as power supply one which can withstand a range outside 200-350W/24-35V/10-20A.

It reduces the overheating rate of the device even with more than twice the output current compared to other devices, thereby increasing both the cost-effectiveness and safety of the device by reducing the program error rate.

Important note: It is particularly recommended to use the SMPS type, as overcurrent within an electrolytic vessel increases in higher longitude areas (e.g. in America, Europe, Southeast Asia, etc.) and can thus cause program errors. With devices from other manufacturers, this leads to crashes and failures, which can mostly be solved by switching the device on and off and are just annoying, but sometimes also require the devices to be sent to the dealer.

Automatic descaling of the electrodes through automatic polarity reversal

Removing mineral deposits is one of the most important maintenance procedures for water ionizers to ensure long-term consistent electrode performance.

While some manufacturers have not yet implemented automatic polarity reversal in their devices, the Allsbon Dion water ionizers do not just have the standard polarity reversal after each use like some other manufacturers, but exceed this with unique polarity reversal technology.

This additional automatic polarity reversal is characterized by extremely fast polarity reversal. The polarity is changed for 15 seconds up to 50 times per second, so that the electrodes are kept free of limescale even more effectively and the valuable platinum electrodes are even better protected against corrosion. This gives the Allsbon water ionizers another unique selling point that sets them even further apart in the high-end range of ionizers. Descaling should still be carried out after one year at the latest, depending on the lime content of your basic water and your usage habits.

A > Video descaling instructions can be found here.

Flexible, particularly long outlet tap made of special, lime-repellent plastic

This clever choice of material (biocompatible and food-safe) keeps the outlet free of any limescale accumulation in the long term, so that the descaling intervals are even longer than with other devices.

The device also has an intelligent automatic switch-off. If, for example, there is a water leak or there is insufficient water supply, this function can offer valuable protection against water damage.